CUTTING OIL FOR ALL HARD-TO-MACHINE METALS
EXTREME PRESSURE LUBRICANT
WELD-PROOF, ANTI-WEAR
THREADING, DRILLING,
TAPPING, BORING IN HIGHLY ALLOYED STEELS,
WITH CHROME, HEAT-TREATED STEELS
BLIND HOLES OR THROUGH-HOLES
EXCELLENT TOOL RESISTANCE
LESS FREQUENT SHARPENING AND POLISHING
DESCRIPTION
Powerful friction reducer, lubricant, weld-proof, with exceptional oil film resistance. Allows excellent evacuation of chips. Suitable for drilling in all sizes, including very small diameters. Allows deep boring operations in hard metals. Usable in cutting removal operations and in deformation for tapping by spinning. Moreover, this product gives remarkable results in plunging before tapping, rolling, bending of steel tubes, and stamping on steels and stainless. This product highlights the extended life of taps and drill bits.
AREAS OF USE
Manual threading.
Thread chasing.
Thread rolling.
Thread die cutting.
Drilling operations.
Boring and deep boring.
Manual and semi-automatic tapping.
Plunging.
PHYSICO-CHEMICAL PROPERTIES TYPICALS
|
PHYSICAL PROPERTIES OF THE LUBRICATING OIL |
|||
|
PROPERTIES |
STANDARD or METHOD |
VALUE |
UNITS |
|
Appearance |
visual |
Fluid |
nm |
|
Colour |
Visual |
Yellow |
nm |
|
Scent |
Olfactory |
Low |
nm |
|
Density at 20°C |
NF EN ISO 12.185 |
970 |
g/l |
|
Nature of solid lubricants |
- |
Without |
- |
|
Nature of base oil |
- |
Mineral |
- |
|
Kinematic Viscosity Base oil at 40°C Base oil at 100°C |
NF EN ISO 3,104 |
12 10 |
mm2/s-1 mm2/s-1 |
|
Sulphated ash |
NF T 60.144 |
< 1 |
% |
|
Acid index (ai) |
EN 14,104 |
< 0.5 |
mg(KOH)/g |
|
Closed-cup flash point |
NF EN 22.719 |
250 |
°C |
|
Self-combustion point |
ASTM E 659 |
> 300 |
°C |
|
Freezing point |
ISO 3016 |
-20 |
°C |
|
Impurities > 25 µ > 75 µ > 125 µ |
FTMS 791 3005 |
0 0 0 |
number/ml number/ml number/ml |
|
PERFORMANCE PROPERTIES |
|||
|
PROPERTIES |
STANDARD or METHOD |
VALUE |
UNITS |
|
Copper blade corrosion 24h 100°C |
ISO 2160 |
1b |
value |
|
Loss by evaporation 22h at 121°C |
ASTM D 972 |
0.5 |
% mass |
|
SHELL 4-ball test Impression diameter Weld load index |
ISO 20.623 – ASTM D 2266 |
0.48 4,800 |
mm daN |
|
SRV test |
ASTM D 5707 |
0.15 |
coefficient |
|
Elastomer swelling test (dimensional change) |
FTM 791 |
0.8 |
% |
|
Water wash-off resistance at 80°C |
ASTM 1264 |
< 3 |
% |
|
Cold starting torque at -20°C |
ASTM D 1478-63 |
18 |
N.cm |
* nm not measured or cannot be measured
INSTRUCTIONS FOR USE
Shake the aerosol for a few seconds. Moderately spray the drill bits, taps, or thread dies before engagement.
In case of manual threading, spray directly on tubes or round profiles.
PRESENTATION
exists in 5 kg tin: carton of 4 units
exists in drums of 200 kg, sold individually
|
|
"Guaranteed without HFC greenhouse effect"
Aerosol 650 ml
|
Can 5 kg
|
Looking for another product?
|
Discover our entire range by clicking on the photo |
Manufacturing, lubrification, cleansing, protection,
IBiotec® Tec Industries® Service
offers a wide range of products reserved for industrial area
If you wish for :
a free sample
a technical advice
a product data sheet
a safety data sheet
IBiotec® Tec Industries®Service
manufacturer of technical chemical products.
Welcome to our website.
IBiotec® Tec Industries®Service is on : 